Home > Error Codes > Samsung Washer > OC
Samsung Washer Error Code OC
Too much water has entered the tub — an overflow condition.
Also shown as: OE, OF, 0C, 0E, 1 OC Last verified: 2026-10-30
Most likely causes, in order
| Cause | How common |
|---|---|
| Too much detergent causing foam that pushes the water level up | Common |
| A water inlet valve stuck open, so water keeps entering | Common — turn the taps off |
| A faulty water-level sensor reading the level wrong | Less common — service job |
What to try, easiest first
- Turn both taps off straight away — if the valve is stuck open, this is what stops more water entering.
- Switch the washer off for about 30 seconds, then switch it back on. The drain pump should run and lower the water.
- Run a Spin Only / Drain cycle to empty the tub, then check for water on the floor.
- If the tub refills on its own while the washer is off, the inlet valve is stuck and needs replacing — do not use the washer until it is fixed.
Reset procedure
Soft reset (first try): press Power to switch the washer off, wait about 2–3 minutes, switch it back on and restart the cycle. If the code was a one-off sensor glitch, it often clears here.
Hard reset: switch the washer off, unplug it from the wall outlet (or switch its breaker off) for 2–3 minutes, plug it back in and restart. Never open a panel or touch wiring while it is plugged in.
When to call a technician
Call a technician if the tub refills while off, the code returns on an empty tub, or water has reached the floor or nearby walls.
Difficulty, time and cost
| Difficulty | Medium |
|---|---|
| Typical DIY time | 20–30 minutes (editorial estimate, not a quoted time) |
| Part / job cost | $30–$85 for the inlet valve part alone. Part-only range from the part-cost guide; a valve stuck open is not a DIY delay — book service promptly. Prices vary by model and area — treat every figure as an estimate, not a quote. |
Model notes and limits
OC is the current overflow display; older models show OE or OF, and small displays can render OE as 0E (zero instead of the letter O). On some top-load manuals OC/1C is listed as a level-sensor problem — if the tub is not overfull, check the sensor page for 1C.
Front-load and top-load models, AddWash/FlexWash models, and US versus UK displays can show the same fault differently. Always confirm against the manual for your exact model number (on the label inside the door or lid, or on the back of the washer) before ordering a part.
Related codes
Frequently asked questions
Is overflow the same as a leak code?
No. Overflow means the tub itself got too full. A leak code means water escaped the machine. Overflow can cause a leak if it is ignored.
Why did the washer drain by itself after this code?
That is deliberate. The washer drains down to a safe level before it lets you restart, so the tub does not spill when the door opens.
I used extra detergent for a dirty load. Could that cause it?
Yes — excess foam can lift the water level and trip the overflow check. Use the dose for the load size, not the dirt level alone.
Sources
- Samsung Support — Information codes on a Samsung washing machine — https://www.samsung.com/sg/support/home-appliances/check-out-the-information-codes-on-my-washing-machine/ (checked 2026-10-30)
- Solo Appliance Repair — Samsung washer error code list — https://soloappliancerepair.com/comprehensive-guide-to-samsung-washing-machine-error-codes/ (checked 2026-10-30)
- WashingCodes — Samsung top-load washer error codes — https://washingcodes.com/samsung-wa52j8060a-wa52j8700a-top-load-washer-with-activewash-error-codes/amp/ (checked 2026-10-30)